NP205 Transfer Case
Below you will find a detailed list of the NP205 Transfer Case parts that includes complete rebuilt Transfer Cases, bearing rebuild kits, gaskets, seals, small parts, individual bearing, forks and sliders, shafts, chain, sprockets and miscellaneous parts. If you need more information or cannot find the parts you need give us a call, if you would like to save money, ask about our good take out parts (GTO), they are inspected and guaranteed.
Use our online shopping cart, just double click the part number and see additional information, add to cart or proceed to check out. If you need more information or cannot find the parts you need give us a call 888-824-201
Having issues diagnosing problems with your NP205 transfer case?
We can help free knowledgeable technical support! We have a large inventory of rebuilt NP205 transfer cases plus Transfer Case parts. The NP205 is a single piece cast iron case with helical gear driven transfer case with a 1.96:1 reduction in low and 1:1 in high range, it was used in a variety of applications from 1969-1980 in Dodge, Ford, GM. The Ford NP205 has a driver side front output and is available in a “separate” and “direct” versions, the direct version has a female 31 spline input gear and bolts directly to the transmission adapter housing. The “separate” Ford NP205 has a yoke type input and connects to the transmission with the use of a short driveshaft. The GM NP205 has a passenger side front output and is available in fixed or slip yoke output, the 10 and 27 spline versions require drive sleeves to mate to the transmission.
Building an off road truck? The NP205 is widely used because the gear drive unit is much stronger than a chain drive unit. Give us a call and we can help you with interface issues to your desired transmission. The helical gear set in the NP205 is thicker which allows more surface area to distribute the load over a wider surface.
The NP205 was manufactured with manual shift, it is a replacement unit for the earlier units, it is a part time case. The front driveshaft will not receive power when in 2WD the transfer case is gear driven, 1.96:1 ratio reduction in low and 1:1 in high range, and a manual shift. In addition to a rebuilt unit NP205 transfer cases with a 12 month warranty we offer all parts required to rebuild your unit, we have new part and we can provide good used takeout parts to save you money!
Free NP205 Transfer Case parts illustration
Below we provide a NP205 parts illustrations to assist you with the correct identification of the parts you need. Select the parts you require from the the list below and give us a call.
To speak to a Drive Train Expert or to place an order call toll free 888-824-2012!
Need Stronger Parts?
Midwest Transmission can Cryogenic Treat any shaft or gear. This cryo treatment will add 30% in component strength. Call 888-824-2012 for a quote.
Check out our Updated Heavy Duty NP205 Output Shaft 30% or 60% Stronger fits all NP205 Bolt Yokes.
This information tag is located on rear of transfer case near where the driveshaft exits.
Use our online shopping cart, just double click the part number and see additional information, add to cart or proceed to check out.
Rebuilt Tested NP205 Transfer Cases 12 month warranty
Rebuilt Overhaul Bearing Kits NP205 Transfer Case
Small Parts Kits NP205 Transfer Case
Gaskets Seals, O-Rings & Washers NP205 Transfer Case
GASKET & SEAL KITS
GASKET KITS
SEALS
GASKETS & O-RINGS
WASHERS
Bearings NP205 Transfer Case
Shift Forks & Sliders NP205 Transfer Case
FORKS
SLIDERS
SYNCHRONIZERS
Shafts NP205 Transfer Case
This shaft is cryogenic treated this part and make it 30% stronger. NP4106561C
Miscellaneous Components NP205 Transfer Case
Click Images to enlarge and shrink
Minimum order $25.00, Shipping and handling charges will be added.